Current and voltage probes allow the current and voltage to be measured without direct contact with the electrical system. This allows measurement to be done without disconnecting the electrical system.

Showing all 15 results

AEMC JM800 Series – AC Current Probes

  • Current output: up to 3000AAC (continuous cycle for the full temperature range)
  • designed for use on DMMs, power and harmonic, meters, recorders or instruments with AC current ranges

AEMC K Series – DC/AC MicroProbes

  • Measures extremely low level DC from 100uA
  • Outputs signal proportional to total current (DC+AC)
  • Low noise
  • Ultra-compact size and non-contact clamp-on convenience
  • Simple plug-in operation
  • Designed for use with digital multimeters and oscilloscopes
  • No range or mode (AC/DC) switching required
  • CE mark

AEMC LM Series – AC Current Probes

  • Clamping diameter 0.63″ (16mm)
  • Measurement range from 0.1 to 200 Amps
  • Over range up to 350 Amps continuous
  • 1ma/A output (model LM102)
  • 1mv/A output (model LM103)
  • Clothes pin design allows access to tight places
  • Frequency response from 48 to 10kHz
  • Arrow marker clearly assist in proper orientation for power measurement applications

AEMC MD Series – AC Current Probes

  • 600A range with mA or mV output
  • Unique hook-shaped jaws that enable the user to “pry” into or “hook” onto cables
  • Maximum conductor size is 2 x 500kcmil
  • Works as a traditional current transformer with ratio of 1000:1
  • AC/DC outputs available

AEMC MH60 – AC/DC Current Probe

  • Clamping diameter 1.02″ (26mm)
  • Measurement range from 0.5 to 140 Amps AC, 100 Amps Dc
  • Measure AC+DC signals
  • 10mV/A output
  • Automatic compensation for earth’s magnetic influence
  • Battery power (8 hour battery life) or USB continuous
  • Frequency response from DC to 1 MHz
  • Selectable 3 or 30kHz filter selection
  • Push button zero adjust
  • LED indicators for power, overload and filter selection
  • UL 94 V2 self-extinguishing case material

AEMC MiniFlex Series – Flexible Sensors

  • Measure from 0.5 to 3000Arms
  • Accuracy 1% of Reading +- from 0.2 to 0.25A
  • TRMS measurements when connected to a TRMS instrument
  • No core saturation or damage if overloaded
  • Low phase shift for power measurements
  • Measures only AC
  • High frequency models available for oscilloscopes
  • Excellent linearity
  • CE Mark

AEMC MN Series – AC Current Probes

  • “Clothes pin” shape makes them ideal for use in tight areas, such as breaker panels, controller panels, or outlets
  • Jaw opening accommodates conductors up to 0.39″ diameter
  • Measurements from 1mA to 150AAC
  • Designed for DMMs, loggers, recorders, and oscilloscopes

AEMC MN100 Series – AC Current Probes

  • Measurement range of 1mA to 150AAC
  • Jaw opening of 0.78″
  • Accommodates conductors up to 0.47″ in diameter
  • Ergonomic design and easy operation
  • Compact size accommodates hard to reach locations
  • Low phase shift for power measurements
  • Available with mV or mA output signals
  • Constructed with UL94VO flame retardant material
  • Designed for DMMs, recorders, loggers, and oscilloscopes

AEMC MN200 Series – AC Current Probes

  • Small compact size
  • Measurement ranges from 100mA to 240A
  • Frequency response to 10kHz
  • UL approved for both US and Canada
  • Designed to EN61010, 600V CAT III
  • Jaw opening accommodates 250kcmil cables
  • constructed with UL94VO flame retardant material
  • Double insulated construction

AEMC MN300 Series – AC Current Probes

  • Small compact size
  • Measurement ranges from 100mA to 240A
  • Frequency response to 10kHz
  • UL approved for both US and Canada
  • Designed to EN61010, 600V CAT III
  • Jaw opening accommodates 240kcmil cables
  • constructed with UL94VO flame retardant material
  • Double insulated construction

AEMC MR400 Series – AC/DC Current Probes

  • The jaw shape enables users to clamp on to cables or small bus bars
  • Powered by battery or standard external 5V power supply via micro-USB connector
  • Measures up to 1000AAC and 1400ADC (model dependent)
  • Automatic Zero DC reset function
  • Auto Power Off enable/disable function
  • Millivolt output compatible with most equipment and instruments
  • Battery life up to 50 hours
  • Safety rating 600V CATIII

AEMC MR500 Series – AC/DC Current Probes

  • The jaw shape enables users to clamp on to cables or small bus bars
  • Powered by battery or standard external 5V power supply via micro-USB connector
  • Measures up to 1000AAC and 1400ADC (model dependent)
  • Automatic Zero DC reset function
  • Auto Power Off enable/disable function
  • Millivolt output compatible with most equipment and instruments
  • Battery life up to 50 hours
  • Safety rating 600V CATIII

AEMC SL Series – AC/DC Current Probes

  • Low AC and DC measurements
  • measures from 10mA to 100A
  • Dual range selection
  • Unique designed for probing in crowded wiring areas
  • Hall effect sensor technology
  • UL approved for the US and Canada
  • Flame retardant UL94 V2 rated
  • Use with DMMs, voltmeters and other voltage measuring instruments

AEMC SR600 Series – AC Current Probes

  • Measurement range of 100mA to 1200AAC
  • Large jaw opening accommodates up to two 500kcmil conductors
  • Ergonomic design and easy operation
  • Low phase shift for power measurements
  • Available with mA or mV output signals
  • Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
  • UL approved

AEMC SR700 Series – AC Current Probes

  • Measurement range of 1mA to 1200AAC
  • Large jaw opening accommodates up to two 500MCM conductors
  • Ergonomic design and easy operation
  • Low phase shift for power measurements
  • Available with mA output signals
  • Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
  • UL approved