Shop
ITECH IT8700 Series – Multi-channel DC Electronic Loads
ITECH’s IT8700 series programmable DC electronic load supports up to 16 channels with mainframe extension transient mode up to 25 kHz improving testing efficiency, all with high resolution and accuracy. IT8700 CC, CV, CR, remote sensing, short-circuit and transient mode for increased convenience.
ITECH IT8800 Series – High Power DC Electronic Load
IT8800 series has wide power range 150W~10kW, voltage and current measurement speed up to 50kHz, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance, it has been used in LED lighting, automotive electronics and other fields.
ITECH IT8900 Series – LED Test Programmable DC Electronic Loads
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics. Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port(frequency:20Hz-2kHz),I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50kHz. IT8900 series provides CR-LED / CC / CV + CC / CR / CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
APM EL Series – DC Electronic Load
APM’s EL Series is a high-power density, programmable DC electronic load with three voltage ranges 200V/600V/1200V. It supports CV, CC, CR, and CP, as well as CV+CC, CV+CR, and CR+CC operating modes. Two or more loads can be connected in mater/slave parallel mode to provide more power or current capacity. RS232/RS485 and USB communication interfaces are built-in, while LAN & GPIB communication cards are optional. The EL Series can be applied to battery discharge, DC charging station, and power electronics testing.
- Power: 600-26400 W
- Voltage: 200-1200 V
- Current: 40-2880 A
ITECH IT9100 Series – Power Meters
The IT9100 power meter can provide the maximum input of 1000 V and 50 A and measurement bandwidth of 100 KHz, and can be easily used for measuring voltage, current, power, frequency, harmonics and other parameters. The standard configuration includes USB, RS232 and LAN communication interfaces and also interfaces for USB-based peripheral devices. Users can save the measured parameters into the external storage medium. The basic voltage and current accuracy is 0.1%. Moreover, the power meter has rich integrating functions, such as the active power. It is widely applied in test of motors, household appliances, UPS, etc.
ITECH ITS5300 – Battery Test Charge & Discharge System
ITECH’s ITS5300 is the most accurate battery testing system, and includes ITECH’s power supply and electronic load, internal resistance tester, temperature capture card and ITS5000 battery test software. With this system it is possible to do a charge test in CC/CV and a discharge test for a CC/CR/CP for multi-channel single battery/battery pack simultaneously. Moreover, it can monitor voltage, temperature, and internal resistance of each single battery, generate charge-discharge curves and save test data.
ITECH ITS9500 – Power Supply Test System
The ITS9500 power supply test system is a convenient, practical and cost-efficient testing system, designed for switching power supply tests. The standard 5U unit integrates electronic loads, programmable AC power supplies, programmable DC power supplies, noise analyzers, timing analyzers, digital electric meters, oscilloscope, I/O cards and other instruments. The ITS9500 can be installed on counter tops or inside standard cabinets.
ITECH SAS1000 – Solar Array Simulation Software
SAS1000/L solar array simulation software can accurately simulate the solar array I-V curve, maximum voltage up to 2250V, power can be extended to 1152kW. PV Inverter has fast response time, control, repeatability, high stability, precision and other characteristics. Built-in EN50530 / Sandia / NB/T32004 / CGC/GF004 / CGC/GF035’s SAS model that can easily program test regulations, materials, Vmp, Pmp parameters, simulate I-V curve characteristic output and generate reports, and can test the static & dynamic maximum power tracking performance of photovoltaic inverters.
Jewell Instruments 1000 Series – Digital Panel Meters
- Ideal for line monitoring
- Isolated DC powered for monitoring multiple choices
- Value priced
- 3 1/2 digit readout, full scale 1999 display
ITECH BSS2000/BSS2000Pro – Battery Simulation Test Solution
BSS2000 & BSS2000 Pro software combined with ITECH’s latest high-performance bidirectional DC power supply, IT6000B/IT6000C/IT-M3400/IT-M3600 covers a power range up to 1152kW and can provide users with a wide range simulation solution covering low-power battery module to high-power power battery system simulation. The BSS2000 basic version, BSS2000 Pro version and BSS2000M Multi-channel version of the battery simulating software are products specifically designed for the above test scenarios. It solves the problem of increasing cost of buying and storage of different types of batteries and the battery simulator can be quickly set to different state of SoC without real charge and discharge process, greatly improving test efficiency.
