Shop – Page 4 of 95 – Electro-Meters

Showing 31–40 of 941 results

Isolation voltage: CATIII 600 Vrms, CATII 1000 Vrms
Combines oscilloscope, serial trigger and decoder, spectrum analysis, data logger, and multimeter functions into a convenient and portable design
Available in 100 MHz or 200 MHz bandwidth models
Sample rate: 1 GSa/s (single-channel) or 500 MSa/s (two-channels)
Record length: Up to 12 Mpts
Includes hardware-based true RMS multimeter
IP51 dust/water resistance certified

Combines oscilloscope, serial trigger and decoder, spectrum analysis, data logger, and multimeter functions in a portable design
Available in 100 MHz or 200 MHz bandwidth models
Sampling rate: 1 GSa/s (single-channel) or 500 MSa/s (two-channels)
Record length: Up to 12 Mpts
Allows waveform recording for up to 22 hours
IP51 dust/water resistance certified

Frequency Range: 9 kHz – 8.5 GHz and 100 kHz – 26.5 GHz
Frequency Resolution: 1 Hz
Output Level Setting Range: -55 dBm to +10 dBm
Dynamic Range: 125 dB
Supported Ports: 2/4 ports for S-parameters, Balance Measurements, and Time Domain Analysis
Measurement Capabilities: Q-factor, bandwidth, and Insertion Loss
Power Source Calibration Compatibility: Compatible with R&S NRPxxA/AN and Keysight U2000A/B series USB power meters
ECal Kits Compatibility: Compatible with ECal kits from several manufacturers

Single channel high-precision programmable voltage output:
- SPD1168X: 16 V / 8 A, total power up to 128 W
- SPD1305X: 30 V / 5 A, total power up to 150 W
Stable, reliable, Low ripple and noise: ≤ 350 uVrms/3 mVpp; < 2 mArms
Fast transient response time: < 50 μs
5-digit Voltage, 4-digit Current Display, Minimum Resolution: 1 mV / 1 mA
2.8-inch true color TFT-LCD 240×320 display
2 types of output modes: Two-wire output mode, 4-wire compensation output mode, Max. compensation 1 V

3 independent high precision outputs: Two 32 V / 3.2 A, One 2.5 V / 3.3 V / & 5 V / 3.2 A, totaling 220 W power
4-digit voltage and 3-digit current display, with minimum resolution of 10 mV and 10 mA
Three output modes available: independent, series, and parallel
Compatible design for 100/120/220/230 V power grids, catering to various power requirements

3 independently controlled and isolated outputs: Two 32 V/3.2 A, one 2.5 V / 3.3 V / 5 V / 3.2 A × 1, totaling 220 W
Voltage displayed with 5 digits, current with 4 digits, Minimum Resolution: 1 mV/1 mA (SPD3303X)
Timing function for programmed output steps
4.3-inch true color TFT-LCD display with resolution of 480 x 272
3 types of output modes: independent, series (max 60 V), and parallel (max 6.4 A)

Rated Output Voltage: 40V, 50V, 80V, 160V
Rated Output Power: 180W, 360W, 720W, 1080W
Wide range of output voltage and current, providing high efficiency power supply
Selection between CV and CC priority modes for better protection of equipment under test
Load transient recovery time (Load change from 50~100%): <1ms
Adjustable slew rate of output voltage and current
Setting and readback resolution: 1 mV, 1 mA