The meter’s display consists of 20 LED segments individually driven by 20 comparators divided into a left side set and a right side set of ten comparators each.

The user can select and adjust the three internal reference voltages that are applied respectively, to the left side of the left comparator set, the center point where the two comparator sets are joined in series and the right side of the right comparator set. The meter’s circuitry detects when the input signal corresponds to the voltage at any one of the 20 points along the two comparator divider networks with a step accuracy of better than 0.1%. The meter can be adjusted so that both comparator sets have an equal reference voltage across them which will produce a linear full scale display, or if required, they can have a different reference voltage which will enable each half of the meter’s display to have a different scale or sensitivity.

The post Texmate AM-20 Series – Bargraph Meters appeared first on Electro-Meters.

There are seven header selectable input ranges of 50mV, 100mV, 200mV, 1V ,5V ,10V and 4-20mA. The meter comes standard with a scale of 0 – 100%, but any required scale and unit of readout can be specially ordered. The meter may also be ordered with a dot mode display option.

The AM-30 uses a 30-pin PCB edge card connector or optionally a Push-On™ screw terminal connector may be used (see ordering information on page 8). This bargraph is designed especially for use in process applications where a low cost visual analog indication is required.

The post Texmate AM-30 Series – Bargraph Meters appeared first on Electro-Meters.

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  • AC/DC Current
  • AC/DC Voltage
  • Load Cell
  • Pressure
  • Process
  • Prototype
  • Resistance
  • Temperature*
  • 4 to 20 mA
• Pre-calibrated I-Series Input Signal Conditioning modules, that have span or zero potentiometers, can be interchanged between any I-Series compatible meter, without recalibration, because all of the analog scaling and reference circuitry is self-contained within the module. 5 or 10 V DC excitation is provided for resistance bridge type sensors.
• 24 V DC excitation is available to power external transmitters and 5 or 10 V DC excitation is available for strain-gages, load cells and resistance bridge type sensors.
• A red or optional green 101 segment bargraph.
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC / 95-370 V DC (PS1) or 15-48 V AC / 10-72 V DC (PS2).
• Optional 16 Bit isolated analog output that can be used to drive an external process device such as a chart recorder, remote display, or for retransmission to a central control room. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired span from ± one bar to the full scale range
• Center zero setting, header selectable.
• Provision for external brightness setting switch (by connecting the DIM to the GND pin on the back of the meter).
• Smart averaging (to speed up display response).
• Optional NEMA-4 front cover.

The post Texmate FX-B101Q Lynx Series – Bargraph Meters appeared first on Electro-Meters.

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  • AC/DC Current
  • AC/DC Voltage
  • Load Cell
  • Pressure
  • Process
  • Prototype
  • Resistance
  • Temperature*
  • 4 to 20 mA
• Pre-calibrated I-Series Input Signal Conditioning modules, that have span or zero potentiometers, can be interchanged between any I-Series compatible meter, without recalibration, because all of the analog scaling and reference circuitry is self-contained within the module.
• 24 V DC excitation is available to power external transmitters and 5 or 10 V DC excitation is available for strain-gages, load cells and resistance bridge type sensors.
• High voltage power supply (PS1) 85 – 265VAC / 95 – 370VDC Low voltage power supply (PS2) 15 – 48VAC / 10 – 72VDC
• Optional single or dual setpoints with easy front adjustment
• Dual 5A Form “A” relays or one 5A Form “A” and one 10A Form “C” relays.
• Easy configuration of relays as high or low setpoints.
• Proportional brightness mode for increased effective optical resolution.

The post Texmate BX-B31 Lynx Series – Bargraph Meter appeared first on Electro-Meters.

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  • AC/DC Current
  • AC/DC Voltage
  • Load Cell
  • Pressure
  • Process
  • Prototype
  • Resistance
  • Temperature*
  • 4 to 20 mA
• Optional isolated 16 bit analog output. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span from ± one count to the full scale range of – 1999 to 9999 (12000 counts)
• A Programmable Tricolor (Red-Green-Orange) or mono color (red or green), 101 segment high brightness bargraph. Vertical or optional horizontal format
• Red 4-digit LED display with a range of -1999 to 9999 (12000 counts). Optional green digital display
• Front panel LED annunciators provide indication of setpoint status.
• Two 10 Amp Form C, and two 5 Amp Form A relays available
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC / 95-370 V DC (PS1) or 18-48 V AC / 10-72 VDC (PS2).
• 24 V DC excitation is available to power external 4/20mA transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors.
• Provision to connect an external programming lockout switch.
• Provision for external DIM switch to reduce the brightest display setting by 50%
• Optional NEMA-4 front cover
• Automatic intelligent averaging, smooths noisy signals while providing a fast display response to real level changes.

The post Texmate PL-B101D40 Leopard Series – Bargraph Meters appeared first on Electro-Meters.

• Two 10 Amp Form C, and two 5 Amp Form A relays available
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC / 95-370 V DC (PS1) or 15-48 V AC / 10-72 V DC (PS2).
• Optional isolated 16 bit analog output. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired span from ± one bar to the full scale range
• Provision to connect an external programming lockout switch.
• Optional NEMA-4 front cover.
• 24 V DC excitation is available to power external 4/20 mA transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors
• Dual input modes utilize the FL-B202Q specific IDP4 Universal DC Volts, mA, 4-20mA dual-input module
• Single Input modes are compatible with the entire LEOPARD FAMILY: More than 38 different Plug-in I-Series Input Signal Conditioners

The post Texmate FL-B202Q Leopard Series – Bargraph Meters appeared first on Electro-Meters.

• Two 10 Amp Form C, and two 5 Amp Form A relays available
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC / 95-370 V DC (PS1) or 15-48 V AC / 10-72 V DC (PS2).
• Optional isolated 16 bit analog output. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired span from ± one bar to the full scale range
• Provision to connect an external programming lockout switch.
• Optional NEMA-4 front cover.
• 24 V DC excitation is available to power external 4/20 mA transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors
• More than 38 different Plug-in I-Series Input Signal Conditioners are approved for Texmate’s Leopard Family of meters.

The post Texmate FL-B101Q Leopard Series – Bargraph Meters appeared first on Electro-Meters.

n.b. Special meter inputs can be factory scaled.

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  • AC/DC Current
  • AC/DC Voltage
  • Load Cell
  • Pressure
  • Process
  • Prototype
  • Resistance
  • Temperature*
  • 4 to 20 mA
• Optional isolated 16 bit analog output. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span from ± one count to the full scale range of – 1999 to 9999 (12000 counts)
• A Programmable Tricolor (Red-Green-Orange) or mono color (red or green), 101 segment high brightness bargraph. Vertical or optional horizontal format
• Red 4-digit LED display with a range of -1999 to 9999 (12000 counts). Optional green digital display
• Front panel LED annunciators provide indication of setpoint status.
• Two 10 Amp Form C, and two 5 Amp Form A relays available
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC / 95-370 V DC (PS1) or 18-48 V AC / 10-72 VDC (PS2).
• 24 V DC excitation is available to power external 4/20mA transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors.
• Provision to connect an external programming lockout switch.
• Provision for external DIM switch to reduce the brightest display setting by 50%
• Optional NEMA-4 front cover
• Automatic intelligent averaging, smooths noisy signals while providing a fast display response to real level changes.

The post Texmate FL-B101D40 Leopard Series – Bargraph Meters appeared first on Electro-Meters.

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  • AC/DC Current
  • AC/DC Voltage
  • Load Cell
  • Pressure
  • Process
  • Prototype
  • Resistance
  • Temperature*
  • 4 to 20 mA
• 24 V DC excitation is available to power external transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors such as Load Cells and Pressure Transducers.
• A red, 51 segment high brightness bargraph.
• Red 4-digit LED display with a range of 1999 to 9999 (12000 counts)
• Front panel LED annunciators provide indication of setpoint status.
• Two 10 Amp Form C and two 5 Amp Form A relays available for the BL-B51D40.
• Auto-sensing AC/DC power supply. For voltages between 85-265 V AC/95-370 V DC (PS1).
• Provision for external DIM switch to reduce the brightest display setting by 50%.
• Automatic intelligent averaging smooths noisy signals, while providing a fast display response to real level changes.

The post Texmate BL-B51D40 Leopard Series – Bargraph Meters appeared first on Electro-Meters.

The Tiger 320 Operating System supports an easy to use PC based Configuration Utility Program, which can be downloaded FREE from the web, and programming from front panel buttons.

The T Version supports custom macro programs that can be easily produced with the Tiger 320 Macro Development System (available FREE on the web). The Development System enables programs to be written in BASIC, which can utilize any combination of the hundreds of functions and thousands of registers embedded in the Tiger 320 Operating System.

Characteristics:

• Red, green, or superbright red 7-segment, 1” high LEDs
• 101 segment red, green or tricolor bargraph
• Modular construction
• Front Panel Controls
• Up to 4 input channels
• 6 LED setpoint annunciators
• Sensor excitation
• Single or dual 16-bit Isolated Analog Outputs
• 6 super smart, independently programmable setpoints with 8 selectable functions
• Autozero maintenance
• Plug-in I/O modules
• Dual independent totalizers to integrate input signals.
• Programmable input
• Scrolling display text messaging
• Display text editing
• Auto-sensing high voltage or optional low voltage AC / DC power supply
• Serial output options include RS-232, RS-485, ModBus, Ethernet, DeviceNet or direct meter-to-meter communications.
• Single or dual 16-bit Isolated Analog Outputs
• Dual independent totalizers to integrate input signals.
• Data logging within the meter
• Internal program safety lockout

The post Texmate GI-50EB101 & GI-50TB101 Tiger Series – Programmable Meter Controllers appeared first on Electro-Meters.