Insulation Testers – Electro-Meters https://www.electro-meters.com/product-category/insulation-testers/ Technology for all your measurement needs Fri, 29 Apr 2022 14:20:42 +0000 en-US hourly 1 https://wordpress.org/?v=7.0 https://www.electro-meters.com/wp-content/uploads/images/electro-meters/cropped-EMlogo_square-32x32.png Insulation Testers – Electro-Meters https://www.electro-meters.com/product-category/insulation-testers/ 32 32 DEIF SIM-Q MKII – Insulation Monitor https://www.electro-meters.com/product/deif-sim-q-mkii-insulation-monitor/ Tue, 27 Jul 2021 18:58:08 +0000 https://www.electro-meters.com/?post_type=product&p=16213
  • Insulation monitoring of AC networks of up to 690 VAC
  • Ideal for applications with frequency converters
  • Fault-finding and self-test mode
  • The leakage capacitance is up to 500 μF

    • The post DEIF SIM-Q MKII – Insulation Monitor appeared first on Electro-Meters.

    ]]>     The SIM-Q MKII is particularly suitable for high-end monitoring of AC/DC networks characterised by high leakage capacitance. A low frequency (LF) version of the SIM-Q MKII is available for thruster systems with 5-20Hz frequency variations.

    The SIM-Q MKII uses a patented measuring method, where a ±25 V DC voltage is superimposed to the system being monitored. To be able to eliminate the influence from the monitored network capacitances and AC/DC components, the SIM-Q MKII performs an automatic measuring cycle that will compensate for these.

    Selectable modes

    The ability of the SIM-Q MKII to measure large capacitances results in long measurement cycles due to the charging and discharging of the network leakage capacitance.

    To ensure a fast reacting product during fault-finding, the SIM-Q MKII has been equipped with three selectable modes for optimal performance:

    • Normal mode (IMD type: AC/DC)
      Long measuring cycles and relatively long response time, but immune to disturbances. Depending on the capacitance and DC levels, the response time can be between 10 and 7,000 seconds (2 hours).
    • Fast mode (IMD type: AC)
      Short response time. Used for fault location when several groups have to be switched in/out. The measurement does not compensate for capacitance and DC levels!
    • Test mode
      Used for self-test of warning/relay function and adjustment of set point. When the mode is selected, the relay is activated and the meter shows the actual set point value. Use the knob on the rear side of the housing to adjust set point to desired value, and then select monitoring mode for measuring.

    The post DEIF SIM-Q MKII – Insulation Monitor appeared first on Electro-Meters.

    ]]>         DEIF ADL-111Q96 – Insulation Monitor https://www.electro-meters.com/product/deif-adl-111q96-insulation-monitor/ Tue, 27 Jul 2021 16:13:20 +0000 https://www.electro-meters.com/?post_type=product&p=16210
  • Advanced insulation monitoring of 24, 110 and 220 VDC networks
  • Detects all types of insulation faults – including double faults
  • Configurable alarm with adjustable set point

    • The post DEIF ADL-111Q96 – Insulation Monitor appeared first on Electro-Meters.

    ]]>     The ADL-111Q96 is used to supervise the insulation resistance between an isolated voltage distribution network and an earth/safety cable. The insulation monitor is applicable with DC networks for voltages of 24, 110 or 220 V DC. The ADL-111Q96 has a relay output with adjustable set point, and it can be configured to either NE (normally energised) or ND (normally de-energised).

    The post DEIF ADL-111Q96 – Insulation Monitor appeared first on Electro-Meters.

    ]]>         DEIF AAL-2 – Insulation Monitor https://www.electro-meters.com/product/deif-aal-2-insulation-monitor/ Tue, 27 Jul 2021 16:08:53 +0000 https://www.electro-meters.com/?post_type=product&p=16208
  • Insulation monitoring of AC networks of up to 440 VAC
  • 10 M or 1 M ranges
  • Adjustable warning set point
  • Delay to prevent unwanted warnings

    • The post DEIF AAL-2 – Insulation Monitor appeared first on Electro-Meters.

    ]]>     The AAL-2 from DEIF is an insulation monitor and is used to supervise insulation resistance between an isolated AC voltage distribution network and an earth/safety cable.

    The insulation monitor, AAL-2 from DEIF, is applicable with single-phase and 3-phase networks with/without neutral for voltages up to 440 V AC.

    The AAL-2 has a built-in relay output and an adjustable warning set point.

    The post DEIF AAL-2 – Insulation Monitor appeared first on Electro-Meters.

    ]]>         Yokogawa MY600 – Digital Insulation Tester https://www.electro-meters.com/product/yokogawa-my600-digital-insulation-tester/ Thu, 04 Mar 2021 16:59:43 +0000 https://www.electro-meters.com/?post_type=product&p=1385
  • Featuring enhanced measurement response times of 0.5 seconds and new functionallity for PASS/FAIL Judgement and Polarization Index and Dielectirc Absoprtion Ratio testing
  • Ability to log up to a 1000 data points to internal memory for offline analysis to a PC
  • Automatic LED backlight when working in remote areas with low visibility
  • Large voltage generation and resistance measurement ranges to suit a wide variety of insulaiton types
  • Basic voltage measurement accuracy of +/- 1% of reading and resistance measurement of +/- 2% of reading with the ability to measure up to 4000 MΩ
  • Power off function that minimizes idle time and conserves battery life
  • Built-in auto-ranging for improved resolution at lower resistance levels
  • IP40 Protection Grade for enhanced ruggedness in harsh enviornments

    • The post Yokogawa MY600 – Digital Insulation Tester appeared first on Electro-Meters.

    ]]>     The MY600 Digital Insulation Tester has enhanced operation compared to the conventional model, by using a shortened measurement time and color indicating judging function. This is a new concept in insulation testing and includes enhanced communication to a PC or tablet.

    Measurement Features 

    • Wide Insulation Test Voltages: 50V to 1,000 V
    • AC Voltage: 2 Vrms to 600 Vrms (45 to 65 Hz)
    • DC Voltage: +/- 2 to 600 Vdc
    • Low-Resistance: 40.00 to 4,000 Ω

    Measurement Accuracy

    • Voltage (AC & DC): 0.1% of reading +/- 4 digits
    • Resistance: ±2.5% reading ±8 digit (0.20 to 4000 Ω) ±8 digit (0.00 to 0.19 Ω)

    Learn More

    The post Yokogawa MY600 – Digital Insulation Tester appeared first on Electro-Meters.

    ]]>