• Eagle Signal Controls

Counters
CX200 and CX300 Series- CYCL-FLEX® Programmable Timers

Microprocessor based solid state timer/ counter… housed in CYCL-FLEX® case
Eagle Signal Controls CX200 and CX300 Programmable Timer Series

Features

  • Five time ranges from 19.999 sec. to 199 hrs.: 59 min.
  • Two count rates – accept and display counts from 1 to 19999
  • Two relay outputs – socket mounted for easy replacement
  • Two form C instantaneous contacts and two form C programmed contacts
  • N.O. solid state MOSFET, delayed action switch rated at 1 ampere continuous load current, 0-264 VAC 50/60 Hz or DC
  • Ideal output for switching low level signals and high voltage loads due to MOSFET output’s ON resistance of 0.5 ohm and very low OFF leakage
  • Programmed outputs operate in one of four load sequences; OOX, OXO, OOX with pulse output, and OOX pulse output with repeat cycle operation
  • Standard start is defined as ON delay reset timer or counter
  • For standard start units, timer/counter resets on power failure
  • Reverse start or OFF delay units will not reset on power failure and will continue cycle when power is restored
  • Non-volatile memory data retention

Description

The CX200 and CX300 are microprocessor based timer/counter housed in a standard 15 terminal CYCL-FLEX® plug-in case. Time or count operation, time range, and standard or reverse start operation is selected by 7 miniature rocker switches located inside the unit housing. Time or count setpoints are entered into the unit using a sealed membrane keypad on the front of the unit. Each digit in the setpoint is individually increased or decreased by pressing the appropriate keypad switch.
Time or count setpoint and progress is displayed on the front of the unit by a 4 1/2 digit liquid crystal display with .5 inch digits. Time or count subtracts from the setpoint and the output changes state at zero. Operational mode annunciators also appear in the display area on the front of the unit. The mode annunciator flashes when the unit is timing or counting.

IIII [+] Read More

The SET and ENT keys provide access to the setpoint, as well as to the front panel programmable software functions. These programmable functions control the pulse output length, setpoint to zero or zero to setpoint cycle progress indication, and count input scale factor. The software programming functions are indicated by prompts to help the user program these functions without the need for written instructions.

The CX series has 2 relay outputs,; 2 form "C" instantaneous contacts, and 2 form "C" programmed contacts. The relays are socket mounted for easy replacement. Outputs can be programmed to operate in one or four lead sequences

 
  • Literature
  • Specifications

Literature and Technical Information

pdf icon

Digital Programmable Timer

CX200 and CX300 Series

++ CX200 and CX300 Series, Percentage Timers| Brochure (151 kB)
++ CX200 and CX300 Series, Manual | (401 kB)
CX200 and CX300 Digital Reset Counters / Timers
 
Display: 4 1/2 digit liquid crystal display with .5 inch digits
Reset Time: 30 ms following voltage removal from simulated clutch input (CR1)
Time Ranges:
Sym Maximum Range Minimum Range
1 19999 Cts. 1 Ct.
2 19999 Cts. 1 Ct.
3 199.99 Sec. .01 Sec.
4 1999.9 Sec. .1 Sec.
5 19.999 Sec. .001 Sec.
6 199 Min.: 59 Sec. 1 Sec.
7 199 Hr.: 59 Min. 1 Min.
Operating Voltage/Frequency:
Sym Dial Range
A6: 120 VAC, 50/60 Hz
B6: 240 VAC, 50/60 Hz
K6: 208 VAC, 50/60 Hz
Time Inhibit/Count Line Voltage/Frequency:
Sym Dial Range
A6: 120 VAC, 50/60 Hz
B6: 240 VAC, 50/60 Hz
K6: 208 VAC, 50/60 Hz
Accuracy:
Setting Accuracy: Time: ±0.1% or 50 ms, whichever is larger (0° to 60°C) Count: 100%
Repeat Accuracy: Time: ±0.001% of setting or 35 ms, whichever is larger (0° to 60°C) Count: 100%
Environmental
Operating Temp.: +32° to +140°F (0° to +60°C)
Static Discharge: Unit function is unaffected by a constant 3600 volt peak, 60 Hz discharge applied to the grounded front plate at a relative humidity of less than 25%
Vibration: Unit function is unaffected by 2.5G sinusoidal vibration magnitude in both directions of the perpendicular mounting axes imposed from 10 to 100 Hz
Weight: 2 lb. 14 oz.
Approvals: UL Recognition E96337
CSA Certification LR26861
Dimensions: 96.82 mm x 107.95 mm, 146.05 mm deep