• Eagle Signal Controls

Counters
MAX Position Advanced Digital Panel Meters

Position Indicator with Presets and Outputs
Eagle Signal Controls MAX Position Advanced Series, position indicator Meters

Features

  • Bidirectional (go thru zero) counter
  • Non-Volatile counter operation.
  • Four user programmable preset setpoints
  • Programmable reference setpoint
  • Programmable Operation; A-B, A+B, Quad
  • Programmable 6 decade correction constant
  • Selectable Input logic; x1, x2 and x4
  • STOP/HOLD, REFERENCE ENABLE, OUTPUT DISABLE and REFERENCE Control inputs
  • 4 Wire / 2 Wire RS-485 Provides LOCAL and REMOTE process Control Capability Modbus RTU protocol
  • FRAM Memory for Setpoint storage
  • Built In Self- Diagnostics
  • Eight Alpha Numeric, 14 Segments LED display
IIII [+] Read More
  • *Automatic and Manual Preset Sequencing
  • *Common Early Warn Preset Programming
  • Batch / Total / (*Cycle Reset) Reset input
  • Output Control (*Step Forward) input
  • Non-Volatile Memory (FRAM) for Counters & Programmed parameters
  • Built In Self- Diagnostics
  • Eight Alpha Numeric,14 Segments LED display

Description

“MAX Position Advanced” is a programmable position indicator and preset counter with a Reference input and set point, four position presets and eight complimentary outputs. Go through zero counting, plus / minus operation, non-volatile counter and ‘on the-fly’ programming features satisfy many process applications. A six decade calibrator is provided for increased display resolution.

IIII [+] Key Features
  1. Bipolar Six Decade Counter (+/-999999)
  2. Six Decade Input Calibrator
  3. DC to 40kHz Count Rate
  4. DC to 20kHz Quadrature Input Rate
  5. Programmable Input Logic (x1,x2, or x4)
  6. Four Programmable Bipolar Preset Limits
  7. Eight Solid State Preset Outputs
  8. Counter Presetting with Reference Input
  9. +12VDC @ 175mA Transducer Supply
  10. 85-265 VAC Operation (12VDC Optional)
 
  • Literature
  • Specifications

Literature and Technical Information

pdf icon

Digital Rate Meters – Position indicators

MAX Position Advanced Digital Panel Meters

++ MAX Position Advanced Series| Brochure (1.2 MB)
MAX position Advanced Series
Display:
Display: Eight Alpha Numeric, 0.4" red LED
Annunciators: Three Annunciators RUN, SET, PGM
Decimal Point: User programmable
Range: xx.xxxx to xxxxxx
Position Counter:
Range: +/- 6 Decades
Presets: 4 Individual; A, B, C, D
Operation: Non-volatile unidirectional or Bidirectional with following modes
A-B, A+B, Quadrature
Count Rate: 40 kHz x1, 20 kHz x2, 10 kHz x4
Outputs: Fixed assignment Solid state
outputs for >/= and < comparisons
Calibrator:
Type: 6 Decade, 0.00001 to 9.99999
Position Inputs:
Input Frequency: 40 kHz x1, 20 kHz x2, 10 kHz x4
Input Type: Single ended, Current Source
Input Logic: Programmable x1, x2 and x4
Input High Level: 3.25 VDC min.
Input Low Level: 1.75 VDC max.
Input Impedance: 1.0 kΩ to common
Input current: 3.25mA. steady state
Input Response: 10μs. min high and low time
Control Inputs:
Input Frequency: DC to 20Hz typ (320μs pulse width for reference input)
Input Type: Single ended, current sinking
Input Logic: Both edge & level sensitive as defined by Input use.
Input High Level: 10 VDC min. to 20 VDC max
Input Low Level: 0VDC min. to 2 VDC max.
Input Impedance: 4.7kΩ pullup to +12 VDC
Input current: 2.5 mA. Steady state
Input Response: 25 ms. make and break time
(310μs pulse width for reference input)
Control Outputs:
Range: 8 Solid State Outputs, 100mA sink max., 24 VDC max.
Assignment: Outputs have fixed assignments.
OUT 1 Position > ‘A’ preset
OUT 2 Position < ‘A’ preset.
OUT 3 Position > ‘B’ preset
OUT 4 Position < ‘B’ preset.
OUT 5 Position > ‘C’ preset
OUT 6 Position < ‘C’ preset.
OUT 7 Position > ‘D’ preset
OUT 8 Position < ‘D’ preset.
Where ‘>’Means greater than or equal and ‘<’ means Less than
Logic: Output ‘FOLLOW’ counter value
Communications:
Serial Interface:

RS-485 compatible (4 or 2 wire options with modbus support)
ModBus RTU
Selectable; OFF,1200, 2400, 4800 or 9600 Baud

Environmental
Enclosure: Plastic Moulded
Operating Temp.: -15°C to +65°C
Storage Temp.: -30°C to +85°C
Input Power: 85-265 VAC, 50-60Hz, 20 VA
12 VDC @ 0.5A. Optional
Accessory Supply: 12 VDC @ 175 mA.
Burden: Motor: 2.45 VA, 120 VAC
Clutch: 10.5 VA
Weight: 2 lb. 14 oz.
Approvals: CE
Enclosure: Plastic Moulded
Dimensions: 2.0” High x 4.0 Wide x 5.56”Deep
Cutout: 1.77”[ 45mm] x 3.62” [92mm]