Model SR661 [Cat. 2113.49] AC Current Probe (BNC) 100mV/A-10A;10mV/A-100A; 1mV/A-1000A max)

AEMC Model SR661 [Cat. No. 2113.49] AC Current Probe (BNC)  100mV/A-10A;10mV/A-100A; 1mV/A-1000A max)
  • Measurement range of 100mA to 2000AAC
  • Large jaw opening accommodates conductors up to two 500MCM
  • Improved ergonomic design and easy operation
  • Conforms to EN 61010, 600V Cat. III
  • Low phase shift for power measurement
  • Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
  • UL approved for Canada and United States
  • Power quality measuring
  • Large industrial loads
  • Measuring around cable bundles
  • Power load monitoring
  • Waveform analysis
Product Description:
space The SR661 is a range selectable probe that offers 3 switch selectable ranges of 20, 200 or 2000AAC. This probe has a voltage output proportional at the current measured in the jaw of the probe. The SR661 has an integral 6.5 ft (1.98m) lead terminated by BNC connector. The high accuracy and wide frequency response makes this probe an excellent choice for use with oscilloscopes.
Nominal Range 20Apk, 200Apk, 2000Apk
Measurement Range 0.1 to 2000Apk
Output Signal(s) mV output signal (2V Peak max), 3 range switch selectable on handle100mV/A: 10mA to 20A Peak;10mV/A: 0.1A to 200A Peak;1mV/A: 1A to 2000A Peak
Accuracy (10A Range)0.1 to 12A ≤3% ± 10mV
Phase Shift(10A Range) 0.1 to 0.5A
0.5 to 2A
2 to 10A ≤15°
10 to 12A ≤15°
Accuracy (100A Range)0.1 to 120A ≤2% ± 5mV
Phase Shift (100ADC Range) 0.1 to 5A
5 to 20A ≤15°
20 to 100A ≤10°
100 to 120A ≤5°
Accuracy (1000A Range)1 to 1200A ≤1% ± 1mV
Phase Shift (1000ADC Range) 1 to 50A
50 to 200A ≤3°
200 to 1000A ≤2°
1000 to 1200A ≤1°
Overload 12A and 120A continuous/1200A for 40 min ON, 20 min OFF
Frequency Range 1Hz to 100kHz (@ -3dB) See typical response curves
Load Impedance 1MΩ, 47pF
Crest Factor ≤6
Working/Common Mode Voltage 600Vrms
Output Termination 6.5 ft BNC
Operating Temperature -14° to 122°F (-10° to 50°C)
Storage Temperature -4° to 158°F (-20° to 70°C)
Operating Relative Humidity 0 to 85% @ 35°C
Jaw Opening 2.25″ (57mm) max
Maximum Conductor Size 2.05″ (52mm)
Maximum Bus Bar Size One 1.95 x 0.19″ (50 x 5mm)
Dimensions 4.37 x 8.50 x 1.77″ (111 x 216 x 45mm)
Weight 1.21 lbs (550g)
Polycarbonate Material Handles: Polycarbonate + ABS, Gray, UL94 V0. Jaws: Polycarbonate, Red, UL94 V0
Electrical EN 61010-2-032
UL Approval Yes – Canada and United States
Double Insulation Yes
CE Mark Yes
SR661 Downloads: Specifications
The Model SR661 is designed for use in industrial and utility environments. The unique ergonomic design allows it to easily clamp onto cables or small bus bars. It is built to the highest safety and performance standards including the CE Mark and is UL approved for Canada and United States. Excellent transformation and low phase shift, plus a broad frequency response, permit accurate measurements of current for power and power quality measurements. The high quality magnetic cores and uniform windings provide sensitivity for very low level current measurements, as well as measurements up to 1200AAC. The Model SR661 provides an accurate voltage output of 1mV/A to 100mV. This voltage output enables instruments without current ranges to measure, display log currents through an AC voltage range or measure very low AC. index mail web