|
|
|
| |
|
| |
| |
|
|
| |
| |
|
|
| |
- Highest-speed -slewing speed: 2,200 mm/s in the Y-axis, 2,000 mm/s in the X-axis
- The use of new, high-torque DC servomotors and pen mechanism results in the highest speed and excellent phase characteristics.
- Acceleration: 7.6 G in the Y-axis; 5.1 G in the X-axis (one-pen model)
- Two-pen model is 7.0 G in the Y axis, and 4.5 G in the X axis. By combining high slewing speed and acceleration, the 3023 & 3024 can capture fast-changing signals.
- High-quality traces by using disposable, quick-change felt-tip pen cartridges, and by a light-weight, fast response pen mechanism
- Top level accuracy of ±0.2%
- Quick, convenient operation:
Major design features include the addition of convenient servo ON/OFF and polarity reversal switches, and pre-amplifiers separated from the input terminals for safety input wiring.
- Electrostatic paper holdown with backlighted LED for accurate paper alignment.
- A choice of frontor rear input model, and oneor two pen model.
- Ten scales of calibrated (standard).
- Versatile remote controls.
- Excellent frequency characteristics.
|
|
|
| |
| |
|
|
| |
| |
The 3024is a top-level, high performance A3 X-Y recorders,available in frontor rear-input models, and one-or two-pen models. All models offer the fastest slewing speed and acceleration. The slewing speed and acceleration of the one-pen model in the Y axis is 2,200 mm/s 7.6 G, and 2,000 mm/s 5.1 G in the X axis. |
|
| |
| |
|
|
|
| |
- Drive System: Automatic null-balancing DC servo mechanism
- Writing Area (Effective Recording Span): X-axis 381 mm (15"), Y-axis 254 mm (10")
- Number of Pens: 1 or 2
- Writing System: Ink writing using disposable felt-tip pen cartridges
- Ink Colors: Red for Y1 1st pen, green for Y2 2nd pen
- Basic Accuracy: ±0.2% of effective recording span (including non-linearity and dead band) at 23 ±5°C on 25 mV/cm range
- Error between Ranges: Less than ±0.1% of pen deflection
- Deadband: Less than 0.1% of effective recording span
- Slewing Speed (Nominal): X-axis 2,000 mm/s, Y-axis 2,200 mm/s
- Acceleration (Nominal): One-pen model ... X-axis 5.1 G, Y-axis 7.6 G, two-pen model ... X-axis 4.5 G, Y-axis 7.0 G
- Pen Lift: All pens simultaneously lifted or lowered by PEN UP-DOWN switch on the front panel, or by an external contract or TTL-level signal
- Chart Paper: A3 size graph paper
- Paper Holddown: Electrostatic paper holddown with LED spot paper alignment
- Type of Input: Rear input. Floating, guarded and shielded (polarity reversal switch on the front panel)
- Input Ranges: 50 μV/cm, 0.1, 0.25, 0.5, 1, 2.5, 5, 10, 25, 50 mV/cm, 0.1, 0.25, 0.5, 1, 2.5, 5 V/cm (16 calibrated ranges plus continuous vernier between ranges)
- Zero Set: Adjustable to any point on the writing area
- Input Impedance: Approx. 1 Mohm constant on all input ranges
- Maximum Source Resistance: 10 kohm
- Zero Stability (Nominal): ±( 1.5 μV + 0.02% of effective recording span)/°C
- Maximum Allowable Input Voltage (Continuous): 50 V DC on 50 μV/cm to 50 mV/cm ranges, 250 V DC on 0.1 V/cm to 5 V/cm ranges
- Maximum Common Mode Voltage: , 130 Vrms AC, or 180 V DC
- Common Mode Rejection: More than 140 dB at power line frequency or at DC
- Normal Mode Rejection: More than 50 dB
- Offset Input: Selectable to ±20, ±40, ±60, ±80, ±100 cm (10 ranges) or 0 (OFF) by front panel dial
- Time Base (Standard): Sweep rates ... 0.25, 0.5, 1, 2.5, 5, 10, 25, 50 s/cm & min/cm (accuracy: ±0.5%), Pens automatically lifted after sweep or reset. Trial sweep available with pens lifted
- Operating Position: Horizontal, vertical or inclined
- Dielectric Strength: 1,000 V AC for one minute between power line and case, and between input-guard terminals and case
- Insulation Resistance: More than 100 Mohm at 500 V DC between power line and case, and between input-guard terminals and case
- Power Requirements: 100, 115, 200 or 230 V AC (must be specified), for both 50 and 60 Hz
- Weight: One-pen model ... approx. 17 kg (37.5 lbs), two-pen model ... approx. 18 kg (39.7 lbs)
|
|
|
| |
|
|
| |
| |
|
|
.jpg){kind=small}
Downloads:
.jpg){kind=small}
