|
The quality of the power supply?
Wave window trigger Instantaneous
power failure
Sag
Impulse
Trigger sensed
Level window trigge Wave-window trigger
Want to monitor data remotely?
Fax modem function
With the OR100E
you can set up a wide-area
data collection network over telephone lines using
commercially available fax/modem PC cards. This
eliminates constraints on the physical distance between
the oscillographic recorder and the monitoring station.
Temperature Measurement
In addition to the direct measurement capability (up to
500 Vrms), the new OR100E includes a temperature
input adapter (788041-1) that works with type
K thermocouples. The adapter is powered by the
OR100E, so there’s no need for a special power
supply when you use the recorder in the field or take
long-duration measurements. The OR100E has
a special temperature input adapter range (see the diagram
on the right) for easy setup.
(Screenshot)
Data Recorder Functions
using a PC card
The OR100E lets you write measurements continuously and in real time to an ATA flash memory
card (PCMCIA card). This means internal memory capacity is no longer a limitation on total recording time*1,
allowing you to take long-duration measurements previously handled by data recorders. You can also display
measured data stored in flash memory on the OR100E display for easy field checks.*2 In addition,
ACRAWin32 is available to assist you in making reports when handling massive amounts of data.
*1 : Maximum sampling rate: 1.6 kS/sec;
*2 : Displays 128 kdata/ch steps
Four-mode power supply
for field use
In addition to working with a 3.5-hour* rechargeable
battery (788021), the OR100E/OR300E also can be
powered by an AC adapter (100–240 V), DC adapters
(12 V/24 V/48 V), and alkaline batteries. Choose the
power supply type that best fits your needs.
Powerful Trigger Functions
The OR100ESeries provides powerful trigger functions for reliable measurement of monitored parameters.
In Normal Trigger Mode, triggers are set for the rise and fall levels. Wave-window Trigger Mode allows you
to monitor for power supply waveform abnormalities in real time. In addition, pre-trigger settings may be set as
desired.
Sharp Display, Calculation Functions and High-Quality Recording Functions
Measurements are clearly displayed on a 5.7-inch backlit LCD display. You can view captured data and print out just the areas
you need. Other capabilities include real-time recording, X-Y display and recording, and transient measurement (memory
sampling when a trigger is sensed during real-time recording). |
|
|
|
|
| |
|
| |
| |
|
|
| |
| |
|
|
| |
- Compact, lightweight and slim. Notebook size (B5) 4-channel isolated recorder
- Fax/modem capability using a PC card
- Powerful trigger functions
- Four-mode power supply for field use
- Standard external interfaces for flash ATA memory card and RS-232 communication
- Temperature measurement using thermocouple
- Data recorder function enabling extended-duration measurement
|
|
|
| |
| |
|
|
| |
| |
The OR100E series of Handy Oscillographic Recorders are complete multi-purpose recorders featuring up to four isolated analog input channels, fax/modem capability using a PC card, four-mode power supply and powerful trigger functions. |
|
| |
| |
| |
|
|
|
Measurement input
- Input type: Floating unbalanced input, I/O isolation (channel independence)
- Zero position: Can be moved within measurement range; null function included.
Frequency characteristics (with filter off): DC to 40 kHz
(+1/-3 dB, typical)
Common mode rejection ratio (CMRR):
85 dB or greater (50/60 Hz; signal source resistance of 500 ( or less)
- Low-pass filter: 5 Hz, 500 Hz, off
Attenuation characteristic;-6 dB/octave
Noise (with filter off, 10 mV/div range input shorted): 2.0 mVp-p (typical)
- AD resolution: 12 bits (equivalent to 11bit internal processing resolution)
- Maximum sampling speed: 400 kS/s (all channels simultaneously; 80 kS/s in wave-window)
- Input impedance: 1 M ± 1%, 5 pF (at 40 kHz, typical)
- Input terminal: Safety terminal (for banana plug)
- Maximum input voltage and maximum floating voltage:
Between H and L input terminals, between H-L input terminal and ground
- Temperature input (with temperature input adapter)
- Scale : Both upper and lower limits can be set in increments of 10*C.
- Position : Can be moved in increments of 10*C.
- Low-pass filter : 5 Hz (fixed)
- Measurement range and accuracy : (at temperature of 23.5*C, following 30-minute warmup period)
Memory function
- Time axis: 200, 500 μs/div
1, 2, 5, 10, 20, 50, 100, 200, 500 ms/div
1, 2, 5, 10, 30 s/div
1, 2 min/div
- Time axis resolution: 80 points/div (measurement period is 1/80 of time axis)
- Memory recording length:
10, 20, 50, 100, 200, 400, 800, 1600, 3200*1, 6400*2 div
*1: Only works on odd-numbered channel when two channels are
connected together.
*2: Only works on channel 1 when four channels are connected
together.
- Number of memory division blocks:
32 maximum--varies depending on installed memory length, set
memory length and whether or not wave window trigger is used.
- Auto functions: Automatic printing, automatic statistical calculations, automatic
saving (to external memory), automatic dialing (for faxing)
Cursor functions:
- One cursor: Measurements on all channels displayed simultaneously.
- Two cursor: Time on all channels, as well as measurement
differences or frequencies
- Cursor calculation function: max/min/ave/rms for cursor range, surface area of cursor range
Recording
- Recording paper:Thermal paper roll (111 mm (width) x10 meters), effective recording
- width: 104 mm
- Paper feed accuracy: ±3%
- Chart speeds: 2, 5, 10, 30 s/div; 1, 2, 5, 10, 30 min/div; 1 hour/div
Recording formats:
- T-Y recording: 4 analog channels + 8 logic bits; 1, 2, and 4 division recording
capability (logic recording can be turned on/off separately for each bit)
- Digital recording: measurements are recorded as digital values.
- X-Y recording: X1-Y1, Y2, Y3. X axis is always 1 channel only.
Recording size: 8 div x 8 div (80 mm x 80 mm)
- Recording format options: Dots, lines
- Recording length: 20 div, 200 div, 800 div, continuous
- Recording line types: Three line thicknesses (analog waveforms)
Printing function
- Printed information: List (settings), scale (units), time print marker, chart speed, chart
speed modification point marker, trigger sensing position, trigger time,
trigger sensing channel, grid (thin line, baseline, off), channel
number, TAG, etc.
- Comments: Character string (20 characters per channel) or channel
information printed in 100 mm intervals.
- Channel number: Channel number or TAG name (7 characters per channel) printed on
waveform.
Real-time & memory
- Description of operations: Normally memory sampling starts when trigger is detected
during real-time recording.
Normal Trigger
Trigger sources: Analog channels 1-4, logic A and B, external trigger input, manual, timer
- Trigger modes: Free, Single, Repeat
Trigger combinations (conditions): AND/OR
- Analog trigger types: Rise, fall, high, low, bi-slope,
level window (in, out)
- Trigger level setting: 1% FS increments
Memory function
Time axis: 200, 500 μs/div
1, 2, 5, 10, 20, 50, 100, 200, 500 ms/div
1, 2, 5, 10, 30 s/div
1, 2 min/div
- Time axis resolution: 80 points/div (measurement period is 1/80 of time axis)
- Memory recording length:
10, 20, 50, 100, 200, 400, 800, 1600, 3200*1, 6400*2 div
*1: Only works on odd-numbered channel when two channels are
connected together.
*2: Only works on channel 1 when four channels are connected
together.
- Number of memory division blocks:
32 maximum--varies depending on installed memory length, set
memory length and whether or not wave window trigger is used.
Auto functions: Automatic printing, automatic statistical calculations, automatic
saving (to external memory), automatic dialing (for faxing)
Wave-window trigger
- Trigger modes: Single, repeat, free
- Frequencies: 50 Hz, 60 Hz
- Trigger combinations (conditions): OR on each analog channel
Method for creating reference waveform:
- Automatically generated from current input or specified parameters
- Reference waveform parameters:
Amplitude, tolerance, offset (1% increments for each), phase (in increments
of 1°)
- Trigger delay: -100% to 100% (in increments of 10%)
- Sampling rates: 80 kS/s (1 ms/div), 40 kS/s (2 ms/div), 16 kS/s (5 ms/div),
8 kS/s(10 ms/div)
- Memory length: Memory cannot be linked; maximum memory length for each
channel is one-half that of normal triggers.
Maximum memory length: 800 div
|
| |
| |
|
|
|
| Measurement range (V/div) |
Measurable range |
Accuracy |
| 100mV
200mV |
± 100.0mV |
± (1% of FS + 1mV) |
| FS(20mV/div) |
± 200.0mV |
± (1% of FS + 1mV) |
| 500mV FS(50mV/div) |
± 500.0mV |
± (1% of FS + 1mV) |
| 1V FS(100mV/div) |
± 1.000V |
± (1% of FS + 1mV) |
| 2V FS(200mV/div) |
± 2.000V |
± (1% of FS + 1mV) |
| 5V FS(500mV/div) |
± 5.000V |
± (1% of FS + 1mV) |
| 10V FS(1V /div) |
± 10.00V |
± (1% of FS + 1mV) |
| 20V FS(2V /div) |
± 20.00V |
± (1% of FS + 1mV) |
| 50V FS(5V /div) |
± 50.00V |
± (1% of FS + 1mV) |
| 100V FS(10V /div) |
± 100.0V |
± (1% of FS + 1mV) |
| 200V FS(20V /div) |
± 200.0V |
± (1% of FS + 1mV) |
| 500V FS(50V /div) |
± 500.0V |
± (1% of FS + 1mV) |
| 1000V FS(100V /div) |
± 500.0V |
± (1% of FS + 1mV) |
|
|
| |
|
|
| |
| |
|
|
|
|
|
 |
|
|
|
|
.jpg){kind=small}
Downloads:
.jpg){kind=small}
