| Display |
| Display: |
7-segment LED, 14.2mm |
| Digit height: |
0.56” high digits |
| Color: |
Red or Green |
| Range: |
| Digital Meters: |
-99999 to +99999 |
| Digital Counters: |
-999999 to +999999 |
| Number of Digits: |
| Digital Meters: |
5 digits |
| Digital Counters: |
6 digits |
| Accuracy: |
|
| DCV & DCA : |
0.01%FS + 1 Count |
| ACV & ACA : |
0.1%FS + 1 Count |
| RTD Temperature : |
0.04°C |
| T/C Temperature : |
0.1°C |
Process Monitor : |
0.01%FS + 1 Count |
| Strain Gauge: |
0.01%FS + 1 Count |
Load Cell : |
0.01%FS + 1 Count |
| FR Counter/Timer: |
±2ppm |
VF Counter/Timer |
0.015% |
| QD Quaduture Input |
±2ppm |
| Digital Meter Conversion: |
| Update rate: |
60/sec. @ 60Hz operation; 50/sec. @ 50 Hz operation |
| Output update rate: |
56/sec. @ 60Hz operation; 47/sec. @ 50 Hz operatio |
| Display update rate |
3.5/sec. @ 60Hz operation; 3/sec. @ 50Hz operation |
| Digital Counter Conversion: |
| Update rate: |
1 / period time:
Gate time + 30ms + 2 periods of
the input signal (max): gate time
selectable 0 to 199.99 seconds |
| Output update rate: |
| Display update rate |
| Input Rating |
| AC Current: |
0 to 1 Amp AC; 0 to 5Amp AC; 0-10 Amp AC is a factory option |
| AC Voltage: |
0-120VAC, 0-240 VAC (W/VAR/ PF/PA); 0-150VAC, 0-300VAC (Volt / Freq)
Up to 600 Volts AC available as an option. |
| DC Voltage: |
Up to 600 Volts DC |
| Frequency: |
50/60Hz and 400Hz |
Input Range: |
| Rated current: |
A / W / VAR : 0-200% ; PF / PA : 20-200% |
| Rated voltage: |
V/W/Var: 120%; FPA: 50-120%; Frequency:20-120% |
| Input Frequency Rate |
| Volts, Amps, Hertz: |
45-65Hz up to the 9th harmonic measuring capability
2% of specified accuracy |
| Sustained Input: |
| Rated current: |
A/W/VAR/PF/PA: 200% continuous; 10x rating for 5 seconds |
| Rated voltage: |
V/W/Var/Freq: 120% continous; PF/PA: 150% continous |
| Burdent: |
| Rated current: |
<0.1 VA per element |
| Rated voltage: |
120V; <0.2 VA per element, 240V; <0.4 VA per element |
| Analog Output |
| Power: |
provided by meter, Isolation: Withstand 3750 Vrms, 8mm creepage |
| Accuracy: |
basic meter accuracy ±0.05% of analog output full scale |
| Response time: |
17 milliseconds for unfiltered input, same as basic meter for filtered output |
| Dual Controller option: |
Power is provided by meter, update rate is 56 / second at 60 Hz, 47 / second at 50 Hz |
| Setup: |
Setpoint values may be entered from front panel pushbutton or via RS-232 or RS-485 |
| Output operation: |
Either may be set to operate above or below setpoint, latching or non-latching, or output disabled |
| Filtering: |
Comparison to the setpoints may be from filtered or unfiltered input signal |
| Time delay: |
Selectable time delay of output status change from 1 to 128 readings |
| Alarm status indicators: |
Either of two red LED’s may be set to indicate when output is on or off, or they may be disabled |
| Relay Output: |
10 A at 240 VAC, 8 A at 24 VDC contact rating; safety certification: VDE, UL, CSA |
| Isolation: |
Isolation Coil to contacts :Safety rated to 250VAC, 4.2 kV peak; Between open contacts : Withstand 1 kVrms |
| Response to input signal: |
Pick-up: 26 milliseconds typical; Release: 22 milliseconds typical |
| Optotransistor output: |
Voltage rating: 30VDC; Current rating: 100 mA minimum at 1.2 VDC maximum |
| Isolation: |
Safety rated to 250 VAC, 4.2 kV peak per high voltage test |
| Response to input: |
signal 17 milliseconds typical |
| RS-232 / RS-485 option: |
Power : provided by meter; Isolation: safety rated to 250 VAC, 4.2 kVp per high voltage test |
| Baud rates: |
300, 600, 1200, 2400, 9600, 19200 |
| Type / Signal levels: |
Full duplex (RS-485) / meets RS-232 and RS-485 standards |
| BCD output option: |
Power : provided by meter; Isolation: safety rated to 250 VAC, 4.2 kVp per high voltage test |
| Type / Signal levels: |
Tri-state, stored parallel / LSTTL, CMOS compatible |
| Controls: |
BCD Enable, Hold, Data ready |
| Temperature Range |
| Operating Temp.: |
0°C~55°C, |
| Storage Temp: |
-40°C~85°C, Relative humidity 95% at 40°C non-condensing |
| General |
| Operating Power |
Frequency 47 to 440 HZ and DC,
consumption 5.3 Watts maximum
Universal power supply 85 to 264 VAC, 90 to 370 VDC
Universal power supply 8 to 28 VAC, 9 to 37 VDC |
| Excitation: |
Selectable with shorting jumpers on power supply printed circuit board (normal setting 10 VDC) |
| Outputs |
5 VDC, ±5%, 100 mA max., 10 VDC, ±5%, 120 mA max., 24 VDC, ±5%, 50 mA max. |
Isolation
(power ground) |
Safety rated to 250 VAC, 4.2 kV peak per high voltage test |
| |
| Case: |
NEMA 4 (IP65) 1/8 DIN case made of high impact 94V-0 UL rated plastic |
.jpg){kind=small}
.jpg){kind=small}
