| |
|
|
|
|
| |
|
| |
| |
 |
- 101 segment AC/DC powered bargraph.
- 3/32 DIN, DIN (96 x 144mm ) case easily mounts in thin or thick
panels (up to 2”)
- Red (std), green (optional) or amber (optional) colors.
- Accepts modular input cards
- 2 Analog outputs
- Vertical or horizontal formats.
|
|
|
| |
| |
|
|
|
| |
|
|
A low cost, red or green 101 segment bargraph in a 36x144mm
case with QUICKSET programming, and an optional, independently
scaled, isolated 4 to 20 mA retransmission output. |
|
|
| |
| |
|
|
|
|
| |
| |
- External transmitters or signal conditioners can be eliminated
by directly connecting the sensor to more than 33 I-Series
Plug-in Input Signal Conditioning Modules that include:
| AC/DC Current |
Pressure |
Resistance |
| AC/DC Voltage |
Process |
Temperature* |
| Load Cell |
Prototype |
4 to 20 mA |
| |
Strain-gage |
|
| |
|
|
|
- Pre-calibrated I-Series Input Signal Conditioning modules, that
have span or zero potentiometers, can be interchanged between
any I-Series compatible meter, without recalibration, because all of
the analog scaling and reference circuitry is self-contained within
the module. 5 or 10 V DC excitation is provided for resistance
bridge type sensors.
- 24 V DC excitation is available to power external transmitters
and 5 or 10 V DC excitation is available for strain-gages, load
cells and resistance bridge type sensors.
- A red or optional green 101 segment bargraph.
- Auto-sensing AC/DC power supply. For voltages between
85-265 V AC / 95-370 V DC (PS1) or 15-48 V AC / 10-72 V DC (PS2).
- Optional 16 Bit isolated analog output that can be used to drive
an external process device such as a chart recorder, remote
display, or for retransmission to a central control room. User or
factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across
any desired span from ± one bar to the full scale range
- Center zero setting, header selectable.
- Provision for external brightness setting switch (by connecting
the DIM to the GND pin on the back of the meter).
- Smart averaging (to speed up display response).
- Optional NEMA-4 front cover.
- More than 30 different
I-Series Input Signal Conditioners are approved for
Texmate’s Lynx Family of meters.
|
| |
| |
|
|
| |
|
| |
|
| Display |
| Display: |
101 segment 4” vertical (std),
horizontal (optn), red (std), green (optn) |
| Display Color: |
Red (Std), Green or Super Bright Red
(optn) |
| Positive Overrange: |
All segments flash |
| Negative Overrange: |
First segment of bargraph display flashes |
| |
| A/D Converter: |
14 bit single slope |
| Accuracy: |
±(0.05% of reading + 1segment) |
| Conversion Rate: |
10 conversions per second (Typical) |
| Temp. Coeff.: |
100 ppm/°C (Typical) |
| Warm up time:: |
2 minutes. |
| Analog Output: |
Isolated 16 bit user scalable mA or V |
| OIC (mA out): |
4-20 mA @ 0 to 500Ω max loop resistance |
| OIV (volts out) |
0-10 V DC @ 500 Ω or higher resistance |
| Power Supply: |
AC/DC Auto sensing wide range supply |
| PS1: |
85-265 VAC / 95-370 VDC @ 2.5W max 4.2W |
General: |
| Operating Temp.: |
0 to 60 °C |
| Storage Temp: |
–20 °C to 70 °C. |
| Relative Humidity: |
95% (non condensing) |
| Case Dimensions: |
....3/32 DIN, Bezel: 36x144 mm(1.42”x5.69”)
Depth behind bezel: (4.64") 117.5 mm
Plus 10 mm (0.39”) for Right-angled connector,
or plus 18.3 mm (0.72”) for
Straight-thru connector, or plus 26.5 mm
(1.05”) for Push-On connector. |
| Weight: |
9.5 oz., 12 oz when packed |
|
|
| |
| |
|
|
|
|
| |
| |
 General Specifcations |
|
|
|
|
|
 |
| |
Related urls: |
|
|
| |
- Model BX-35, 96x24mm, Low Profile
3 1/2 Digit, Modular Digital Meters
- Model BX-45, 96x24mm, Low Profile
4 1/2 Digit, Modular Digital Meters
- Model BX-B31, 96x24mm, Low Profile
31 LED Segments Bargraph Meter
- Model DX-35, 1/8 DIN,
3 1/2 Digit, Modular Digital Meters
- Model DX-40, 1/8 DIN,
4 Digit, Modular Digital Meters
- Model DX-45, 1/8 DIN,
4 1/2 Digit, Modular Digital Meters
- Model FX-101Q, 36x144mm,
101 LED Segments Bargraph Meter
|
| |
|
|
|
|
|
|
|
.jpg){kind=small}
.jpg){kind=small}
